How to install the hob with your own hands

What kind of kitchen would do without a stove or a separate hob? Perhaps this is the most important kitchen appliance along with a refrigerator or an oven. This article will tell you in detail how to install the hob without the help of a wizard..

What kind of kitchen would do without a stove or a separate hob?

Hob selection

First you need to know what types of hobs are, what is their difference from full-fledged stoves and which one to choose.

A separate hob is good in that it does not depend on the oven and can be installed anywhere, while a whole niche must be allocated for the stove. A wide range of surfaces allows you to choose the right size, color and material. The only drawback is the high cost..

A wide range of surfaces allows you to choose the right size, color and material.

Before going to the store, you should decide on the type. There are the following.

Gas. This is not to say that this is the most popular type, but such panels are chosen more often, relying on the fact that gas is cheaper than electricity. And also problems with gas happen much less often than with electricity. This means that food can be cooked even by candlelight..
Electric hobs are distinguished by a wide variety of both design and function. In any kitchen interior, the device will look stylish and concise..
Combined – for all occasions. If the electricity is turned off, then the panel continues to work, but with the help of gas. And vice versa.

It is also worth knowing about the materials from which the hobs are made..

Enamel. Differs in reasonable price and good quality.
Steel (stainless). Three words that describe these models: price, durability and style.
Glass ceramics. This is the best material from a technical point of view, but such panels are very expensive..

Bore hole preparation

The hob is easy to install. All steps for correct installation are detailed below..

Installing the hob is easy.

Tabletop layout

Layout is the most important step in preparing for a hob cut-in. The slightest mistake can ruin the appearance of the kitchen, and in the worst case, lead to the need to purchase a new countertop..

Layout is the most important step in preparing for a hob cut-in.

The easiest ways to markup.

Place the panel on the surface and trace the borders with a pencil. The easiest and most accurate method.
Carefully measure the dimensions of the slab and transfer to the intended location.

Tip: It is not recommended to use a marker when stroking, because if visible traces remain, it will be extremely difficult to remove from the surface of the tabletop..

Cutting the bore hole

Either a milling machine or an electric jigsaw is used to cut the hole. First, you should make small holes in the corners of the drawn diagram and use a thin file to walk along the lines of the drawn figure. After the hole has been cut out, insert the hob and check if there are any inaccuracies..

To cut the hole, use either a milling machine or an electric jigsaw..

Advice. For a smoother edge, a small-toothed jigsaw is recommended..

Sealing the bore hole

Sealing the slices is a prerequisite before installing the hob. This is necessary in order to keep the tabletop intact. Because if water gets on the material, the countertop will swell and may start to grow moldy. This will directly affect the hob..

A prerequisite before installing the hob is the sealing of the slices..

Sealing is carried out using a special sealant or nitrocellulose varnish. The product should be applied in a thin layer to the internal cuts. There is no need to apply sealant to the upper part, since this part will be sealed with a special gasket that comes with the stove.

Sealing is carried out using a special sealant or nitrocellulose varnish.

Such a protective tape is glued to the front of the cut. The protective film applied along the entire length does not need to be removed immediately. The tape should be glued around the perimeter without a single cut. At the corners, it is glued with a turn. The ends of the tape are connected carefully without overlapping or creating a gap between them.

Such a protective tape is glued to the front of the cut.

Panel fixing

The hob must be installed with the utmost precision and attention to detail. After the hole has been made and the sealing has been carried out, the panel must be inserted and adjusted so that the front is parallel to the table top..

The hob must be installed with maximum precision and attention to detail..

Further, from the inside of the cabinet, you should fix the stove using special plates that come with the kit. The most important thing is that the installation must be done carefully so that there is no distance between the surface of the countertop and the cooking equipment..

Further, from the inside of the cabinet, the plate should be fixed using special plates that come with the kit.

If everything is done correctly, then the last step is to cut off the remaining adhesive sealing tape with a clerical knife..

Advice. In addition to the usual adhesive tape, manufacturers offer aluminum tape in the kit. It is installed strictly according to the instructions..

Connecting an installed hob

The final stage of installing the hob is connecting to the appropriate power supply. It can be either electricity or gas.

The final stage of installing the hob is connecting to the appropriate power supply

Note! Failure to comply with safety rules can endanger not only your own life, but also the lives of other people.

Electrical panel

The panel’s performance directly depends on the supply of electricity, so you should take care of a convenient and close location of the outlet. Do not forget that grounding is required for the outlet, and the cross-section for the cable must be at least 4 square cm.

The panel’s performance directly depends on the supply of electricity, so you should take care of a convenient and close location of the outlet.

After installing the stove, it is worth plugging the plug into the outlet and check its working condition.

Induction panel

Such a model in the installation is no different from an electric stove. Only some models do not have a cord, so you have to connect the wires yourself.

Such a model in the installation is no different from an electric stove..

Gas panel

During installation, the following safety instructions must be observed.

There must be a ventilation hood in the kitchen..
The distance between the hob and the wall must be at least 13 cm.
The hose going from the equipment to the gas pipe must be in a visible place so that there is free access to it..

Advice. For the sake of safety and reliability, it is recommended to entrust the connection to the gas pipe to a specialist..

There are many videos on the Internet with step-by-step instructions on how to install a gas hob with your own hands. However, there is nothing terrible and difficult in connection..

There are many videos on the Internet with step-by-step instructions on how to install a gas hob with your own hands.

Before starting the installation, you should restrict gas access to the room. Next, the hose from the stove must be screwed to the main gas pipe. It is desirable that at this place there is a valve that turns off the gas.

Before starting the installation, you should restrict gas access to the room..

The place with the thread must be lubricated with grease. After that, you should check this place and the hose for leaks with a soap solution. If bubbles begin to appear in any area, then the thread is not tight. In this case, you need to unwind and repeat all the above steps..

After that, you should check this place and the hose for leaks using a soap solution..

Subject to all installation rules, the hob will delight with durable and reliable operation..

Video: How to install the hob with your own hands?

Kitchen