Do-it-yourself refrigerator door seal restoration.
Every technique breaks down from time to time. And the refrigerator is no exception. Even a minor problem negatively affects the overall working condition. The most common malfunction in a refrigerator is seal wear. This article will tell you in detail how to restore the refrigerator seal without calling the wizard.
Every technique breaks down from time to time. And the refrigerator is no exception.
Features of the restoration of the refrigerator seal
The seal serves as protection against air ingress. This is a rubber layer that allows the door to fit snugly against the body.
If the seal fails, the freezer compartment begins to freeze more ice. Ice can be seen on the back wall. Also, the door does not fit tightly, so a gap appears.
If the seal malfunctions, the freezer compartment begins to freeze more ice.
Note! In order not to waste money, you need to inspect and find the place of damage. If the gum is rotten, then you need to buy a new one, and if it has moved away in one place, then you can simply glue.
Why does the door of a household appliance not close?
There may be several reasons.
- Hinges. Over a period of time, the door fastenings may loosen. This leads to incomplete closing of the door. In this case, screw the bolts well..
- Damage to the casing of the refrigeration unit.
- Loose seal.
Useful information! If the poor closing of the door is due to damage to the refrigerator body, then you should not fix the problem yourself. You need to contact a specialist.
What to do after the old seal is worn out
If the rubber band on the household device is worn out, you must carefully remove it without damaging the surface of the refrigerator. Since factory rubber bands are an integral part, it will not be difficult to remove with your own hands. You just need to pry the corner with a clerical knife and peel it off from the case.
In some cases, you need to remove the door from the case to make it easier to peel off the rubber band.
Since factory rubber bands are an integral part, it will not be difficult to remove with your own hands..
Next, you need to remove the remnants of the glue. A soapy solution or rubber band will do just fine with this challenge. For stubborn adhesives, you may have to resort to using special solvents..
After the surface is dry, you can start gluing a new gasket..
After the surface is dry, you can start gluing a new gasket..
How to choose a sealing rubber
The sealant should be chosen based on the brand of the refrigerator and its model. Elastic bands are of various types and the method of gluing is different. Some have an adhesive backing, while others are fixed with self-tapping screws..
If you screw on the gasket with self-tapping screws, you can damage the enamel of the device. Therefore, an adhesive based seal is the best solution..
The seal should be chosen based on the brand of the refrigerator and its model.
What to do if there is a damaged seal
After diagnosing problems related to the performance of the refrigeration device, many people have a question of what to do if the gum does not fit snugly. Below are all possible ways to deal with this problem..
After diagnosing problems related to the performance of the refrigeration device, many people have a question of what to do if the gum does not fit snugly
Replacing the rubber band
As stated above, you can completely replace the sealing gum. This method is only suitable if the damage is numerous..
As stated above, you can completely replace the sealing gum.
Gluing
For small defects, you can use Moment or Superglue glue. Any shoe glue can be used as an alternative. The effect will be short-lived, but it will help you to postpone spending money on a new gum.
For small defects, you can use Moment or Superglue glue.
Reversing the door
Another way is to hang the door on the other side. Not all models allow such a procedure..
Another way is to hang the door on the other side..
Note! If the rubber gasket is severely damaged, overhanging the doors will have no effect..
Boiling water will help
Remove the seal from the door and put it in boiling water. The gasket should stay in water until it cools completely. After that, it is necessary to allow the rubber material to dry and attach it back to the door. This procedure will help reanimate rubber that begins to dry out..
Remove the seal from the door and put it in boiling water
Good to know! This procedure is well suited for refrigerators that have not been in operation for a long time..
Paper
If the space between the elastic and the door is no more than 3 mm, folded paper will help solve the problem. Cardboard will also work. Fill the gap with paper.
If the space between the elastic and the door is no more than 3 mm, folded paper will help solve the problem..
What is the danger of damage to the seal
It is necessary to take appropriate measures in time if the seal is damaged. If air enters the interior of the refrigerator compartment, the temperature controller makes the compressor run at full capacity. In the process of non-stop operation of the refrigerator, the motor may burn out, which will lead to a complete lack of operation of the device..
It is necessary to take appropriate measures in time if the seal is damaged.
Recommendations
It is worth adhering to some rules so that the technique does not fail..
When buying, choose a technique that has more positive reviews..
Doors can only be opened using the specially designed handle..
Apply silicone grease to seal monthly.
Adhering to the recommendations, you can increase its service life..
